EAD LMO6138 Omnidirectional 690-2700MHz MiMo Antenna for 2G/3G/4G/5G

Article no.: LMO6138-WB-SMSM
Delivery time: Unconfirmed

MiMO omnidirectional antenna with 3dbi gain This omnidirectional antenna has 2 antenna elements for optimal reception in the fast 3G, 4G and 5G networks. ACT7270 is a MIMO (2 port) 5G / 4G / LTE Multiband omnidirectional antenna. Housed in a rugged radome, the ACT7270 is a... read more

1,495 kr

Add to Wish List

MiMO omnidirectional antenna with 3dbi gain

This omnidirectional antenna has 2 antenna elements for optimal reception in the fast 3G, 4G and 5G networks.

ACT7270 is a MIMO (2 port) 5G / 4G / LTE Multiband omnidirectional antenna. Housed in a rugged radome, the ACT7270 is an antenna suitable for outdoor use including recreational and marine environments to improve reception of 5G, 4G (LTE), 3G and GSM signals, especially for wireless broadband and CCTV deployments.< /span>

Vertical antenna frequency range and gain

617-700 MHz 1.0 dBi
700-960 MHz 3.3 dBi
1710-2200 MHz 4.0 dBi
2500-2700 MHz 3.8 dBi
3400-3800 MHz 3.0 dBi

Frequency range and gain of the horizontal antenna

617-700 MHz 0.6 dBi
700-960 MHz 2.2 dBi
1710-2200 MHz 3.6 dBi
2500-2700 MHz 5.7 dBi
3400-3800 MHz 6.9 dBi

The antenna is delivered with 2x15cm antenna cables with SMA male connector for further connection of any length. See accessories for ready-made cable lengths or contact us to have your cable tailored to your needs.

The antenna is approximately 187 mm in height and 106mm at the base. It will be available with or without the wall/pole mount and is fed by two short pigtail cables, allowing longer cables to be connected for specific cabling.

ACT7270 antenna is provided with a gasket and a nut as standard, so that the antenna can be installed permanently with through holes

Alternative mounts for wall or post.

Frekvensområde	690-800/800-960 1710-2170/2500-2700 MHz 3400-3800 MHz
Max gain - Element 1 Max gain - Element 2	1.4 / 2.0 /3.0 / 3.3 dBi 2.8 / 3.0 / 3.9 / 3.9 dBi
Polarisation	Dubbel
Impedans	50 Ohm
VSWR	<2:1
Effekt	10W
Drifttemperatur	-30 Till +70 grader C°
Kabel / Anslutningar	2 x 15cm SMA anslutning
Dimensioner	187 x 106 (h x d) Exkl. monterings bracket

Frekvensområde	690-800/800-960 1710-2170/2500-2700 MHz 3400-3800 MHz
Max gain - Element 1 Max gain - Element 2	1.4 / 2.0 /3.0 / 3.3 dBi 2.8 / 3.0 / 3.9 / 3.9 dBi
Polarisation	Dubbel
Impedans	50 Ohm
VSWR	<2:1
Effekt	10W
Drifttemperatur	-30 Till +70 grader C°
Kabel / Anslutningar	2 x 15cm SMA anslutning
Dimensioner	187 x 106 (h x d) Exkl. monterings bracket

Explanation of frequency bands

When choosing an antenna, pay attention to which frequency bands the antenna supports. Depending on which operator and where the antenna will be used, the frequency bands vary. Larger cities use 2600MHz while smaller towns use 800/900MHz with some support bands in between such as 1800/2100MHz.

A higher frequency band gives a higher speed but also has a shorter range. The same applies to the antenna, if you have a base station that transmits on 2600MHz, your antenna, antenna cable and the location of the antenna become more important than on a lower frequency band. Explanation of signal loss we will go through soon. Higher frequency bands also mean shorter range from the base station.

450MHz (coverage band) also known as the Net1 band is the frequency band that covers the most area in Sweden. Therefore, Net1 is known to be able to have reception where other operators don´t have a chance, but with low download and upload speeds. The reason why this band is called Net1 is because that the company Net1 has exclusive rights to this frequency band.

800MHz (coverage band) is used by all common operators, excluding Net1. The low frequency band means that 800MHz covers a lot of space. Therefore, the band is used outside big cities or smaller towns. 800MHz is the most used frequency band around Europe.

900MHz (coverage band) is the band that Tele2 and Telenor initially used as coverage band. 900MHz is a more unusual LTE band and in the beginning the band caused some problems when the clients (mobile phones etc.) could not connect to 900MHz. Today, the mobile phone manufacturers have adapted the mobile phones to be able to communicate on 900MHz.

1800MHz (capacity band) is the latest frequency band launched. All operators today use this band in metropolitan centers (apart from Net1).

2600MHz (capacity band) is a very well-used frequency band all over Europe. 2600MHz is the highest frequency band used for LTE, this means that the band also has the shortest range compared to 800/900MHz. Due to the high capacity, the band is used in metropolitan environments where many base stations are required to cover as much surface as possible and have as high a capacity as possible.

Frekvensplan 4G