Poynting Riktantenn 4x4 MIMO 5G 11 dBi

Article no.: A-XPOL-0024-V1-01
Availability: 3pcs - Hurry up

Datasheet

Poynting XPOL-24 is their first 4x4 MIMO 5G/LTE band directional antenna with exceptional performance. This is due to the introduction of advanced metamaterial technology, using an artificial magnetic conductor (AMC) and new patented configuration. Which has been shown to prov... read more

4 041 kr

Ord. price 4 490 kr

button_wishlist

Poynting XPOL-24 is their first 4x4 MIMO 5G/LTE band directional antenna with exceptional performance.

This is due to the introduction of advanced metamaterial technology, using an artificial magnetic conductor (AMC) and new patented configuration. Which has been shown to provide exceptional improvements in bandwidth and signal gain.

The radiation patterns of this antenna are exceptionally well controlled, further contributing to the antenna's high performance.

XPOL-24 offers wideband frequency coverage from 617 to 4200 MHz with a maximum gain of 11dBi. The antenna performs exceptionally well in the following frequency bands: 617-960 MHz, 1710-2170 MHz, 2300-2700 MHz and 3400-4200 MHz.

The broadband performance is an important factor for 5G/LTE technology because these is dependent on features such as Carrier Aggregation (CA) to provide the best possible reception and throughput across multiple frequency bands simultaneously. This makes XPOL-24 a good option for current and future 5G/LTE antenna installations.

Exceptional high performance antenna for 5G/4G LTE
New advanced metamaterial technology for high performance
Broadband 4x4 MIMO from 617 to 4200 MHz
Four cross-polarized antennas in a single housing
Weather, dust and vandal resistant housing with IP65 rating

Product sheet PDF (English)

Teknisk specifikation
Frekvensband	617-960 MHz
	1710-2700 MHz
	3400-4200 MHz
Förstärkning	Max 11 dBi
	8,5 dBi på 617-960 MHz
	8,5 dBi på 1710-2700 MHz
	11 dBi på 3400-3800 MHz
Impedans	50 Ohm
Fäste	Ledat vägg- och mastfäste
Placering	Inomhus eller utomhus
Max uteffekt	10W
Antennsladd	4 st 5 meter HDF 195 Super Low Loss
Kabelanslutning	4 st SMA-hane
Storlek	444 x 290 x 110 mm
Vikt	3165 gram
IP Klassning	IP65
Temperatur	-40 till +80 grader
Vindtålighet	160 km/h

Teknisk specifikation
Frekvensband	617-960 MHz
	1710-2700 MHz
	3400-4200 MHz
Förstärkning	Max 11 dBi
	8,5 dBi på 617-960 MHz
	8,5 dBi på 1710-2700 MHz
	11 dBi på 3400-3800 MHz
Impedans	50 Ohm
Fäste	Ledat vägg- och mastfäste
Placering	Inomhus eller utomhus
Max uteffekt	10W
Antennsladd	4 st 5 meter HDF 195 Super Low Loss
Kabelanslutning	4 st SMA-hane
Storlek	444 x 290 x 110 mm
Vikt	3165 gram
IP Klassning	IP65
Temperatur	-40 till +80 grader
Vindtålighet	160 km/h

Explanation of frequency bands

When choosing an antenna, pay attention to which frequency bands the antenna supports. Depending on which operator and where the antenna will be used, the frequency bands vary. Larger cities use 2600MHz while smaller towns use 800/900MHz with some support bands in between such as 1800/2100MHz.

A higher frequency band gives a higher speed but also has a shorter range. The same applies to the antenna, if you have a base station that transmits on 2600MHz, your antenna, antenna cable and the location of the antenna become more important than on a lower frequency band. Explanation of signal loss we will go through soon. Higher frequency bands also mean shorter range from the base station.

450MHz (coverage band) also known as the Net1 band is the frequency band that covers the most area in Sweden. Therefore, Net1 is known to be able to have reception where other operators don´t have a chance, but with low download and upload speeds. The reason why this band is called Net1 is because that the company Net1 has exclusive rights to this frequency band.

800MHz (coverage band) is used by all common operators, excluding Net1. The low frequency band means that 800MHz covers a lot of space. Therefore, the band is used outside big cities or smaller towns. 800MHz is the most used frequency band around Europe.

900MHz (coverage band) is the band that Tele2 and Telenor initially used as coverage band. 900MHz is a more unusual LTE band and in the beginning the band caused some problems when the clients (mobile phones etc.) could not connect to 900MHz. Today, the mobile phone manufacturers have adapted the mobile phones to be able to communicate on 900MHz.

1800MHz (capacity band) is the latest frequency band launched. All operators today use this band in metropolitan centers (apart from Net1).

2600MHz (capacity band) is a very well-used frequency band all over Europe. 2600MHz is the highest frequency band used for LTE, this means that the band also has the shortest range compared to 800/900MHz. Due to the high capacity, the band is used in metropolitan environments where many base stations are required to cover as much surface as possible and have as high a capacity as possible.

Frekvensplan 4G